▶ P02 — COMMERCIAL PRODUCT · GUITAR EFFECT PEDALS

Guitar Effect Pedal Series

Co-developed a commercial series of six guitar effect pedals that run on 3 V, from DipTrace PCB layouts through a shared enclosure drill template and laser-engraved artwork on 75 powder-coated 1590B enclosures, then sold the finished series at a trade show.

6 pedals 3 V supply 75 enclosures

Two finished pedals in black enclosures: the Phaser with blue knobs and the Drippstortion with orange knobs, each with two toggles, a red LED and a footswitch
Phaser and Drippstortion, production units.

Six Pedals, One Enclosure Standard

Clean Boost, Compressor, Distortion (the Drippstortion), Fuzz, Phaser, and Tremolo: a complete pedal line, built to sell. Every circuit runs from a 3 V supply, so the designs are built around rail-to-rail CMOS op-amps (Microchip MCP606x and MCP6V64) and, in the Tremolo, zero-threshold ALD110900 MOSFETs.

All six share the same 1590B aluminum enclosure and control layout: two knobs, two toggles, a status LED, and a footswitch. The PCB layouts place the pots, toggles, and LED to line up with one drilling pattern, and each pedal's artwork was laser-engraved onto the powder-coated lid.

The finished series was exhibited and sold at a trade show.

Product Line
6 Pedals
Supply
3 V
Enclosure
1590B Aluminum, Powder-Coated
Built
75 Enclosures
PCB Tool
DipTrace
Drill Template
FreeCAD
Artwork
CNC Laser Engraving
Market
Sold at a Trade Show

Board Revisions

DipTrace layouts, rendered here straight from the original Gerber and drill files. The Tremolo went through two board revisions before production.

Tremolo Rev A PCB render: two-layer routing with no ground plane and two large round potentiometer footprints in the middle of the board
Tremolo · Rev A · Mar 2021 Signal and power routed across both layers with no ground plane. 192 drilled holes.
Tremolo Rev B PCB render: the bottom layer is flooded with a copper pour and the board is labeled TREM
Tremolo · Rev B · May 2021 Bottom layer flooded with a copper pour, and the layout reworked down to 106 drilled holes.
Drippstortion prototype PCB render with five pots labeled Output, FF cut, Hi-cut, Lo-cut and Input, and a Hard Clip / Clean / Soft Clip switch
Drippstortion · Prototype 98 × 102 mm test board with five pots and a three-way clipping switch.

Prototype to Production

The Drippstortion started as a large prototype board with five controls (Input, Lo-cut, Hi-cut, FF cut, and Output) plus a three-way Hard Clip / Clean / Soft Clip switch.

The production pedal brings that down to two knobs and two toggles on a board that fits the 1590B, the same control layout used across the whole series.

Enclosure & Artwork

1590B lid drill template, 60.5 by 112 mm: two 7.7 mm pot holes at the top, two 6.7 mm toggle holes and an 8 mm LED hole down the centerline, and a 13.2 mm footswitch hole near the bottom. The artwork zone sits between the LED and the footswitch, 22.4 to 41.4 mm from the footswitch end. ARTWORK ZONE limits dashed Ø7.7 POT Ø7.7 POT Ø6.7 TOGGLE Ø6.7 TOGGLE Ø8 LED Ø13.2 FOOTSWITCH 60.5 mm 112 mm 22.4 41.4
Drill Template · 1590B Lid One fully constrained FreeCAD sketch sets the hole pattern for all six pedals. The artwork is held to a 22.4–41.4 mm band from the footswitch end, inside hard limits of 19.2–44.6 mm, so the engraving stays clear of the LED and footswitch.
Artwork layout sheet for six pedals (Tremolo, Compressor, Fuzz, Phaser, Boost and Drippstortion), each drawn on the same lid outline with hexagons marking the shared hole pattern
Laser Artwork · Six Pedals Each pedal's logo laid out on the shared hole pattern, then laser-engraved through the powder coat on 75 enclosures.

Engineering Breakdown

◈

Designed for 3 V

Every circuit runs from 3 V. The parts list is built around rail-to-rail CMOS op-amps (MCP6064, MCP6062, MCP6061, MCP6V64), an MCP6541 comparator, and zero-threshold ALD110900 MOSFETs in the Tremolo.

◈

Rev A → Rev B

Iterated the Tremolo board from Rev A (March 2021) to Rev B (May 2021), adding a bottom-layer copper pour and cutting the drilled holes from 192 to 106.

◈

Layout for Mechanical Fit

Placed potentiometers, toggles, and LEDs in the PCB layouts so they line up with the enclosure drilling pattern shared across all six pedals.

◈

Constrained Drill Template

Drew the 1590B lid's hole pattern as a fully constrained FreeCAD sketch: two pots, two toggles, the status LED, and the footswitch, all dimensioned from the centerline.

◈

Laser-Engraved Artwork

Operated a CNC laser to engrave custom artwork for six pedals onto 75 powder-coated aluminum enclosures, keeping each logo inside a measured band between the LED and footswitch.

◈

Taken to Market

Brought the series to market by exhibiting and selling the finished pedals at a trade show.

Capabilities Used

// ELECTRICAL
DipTrace PCB Design Fabrication
// MECHANICAL
Laser Cutter
Next project · 3 / 5 RGB LED Snowflake →